Iowa Precision Cornermatic Plus® Versa HVAC Ductwork Corner Inserter Machine

Name: Iowa Precision Cornermatic Plus® Versa HVAC Ductwork Corner Inserter Machine
Brand: Iowa Precision
SKU: CM-VERSA
Availability: InStock

The Iowa Precision Cornermatic Plus Versa HVAC Ductwork Corner Inserter Machine was specifically designed to reduce shop labor by addressing the difficulty with inserting corners into duct FITTINGS — from standard fittings to odd fittings like tight square throat elbows, flex connectors, offsets down to 2″ throats, and even the toughest inside or outside angle off-set transition fitting from 16-26 gauge. The Cornermatic Plus Versa was specifically designed to handle any transverse duct connector (TDC) or transverse duct flange (TDF) fitting assembled on a bench and automatically and effortlessly complete eight (8) transverse duct connector (TDC) or transverse duct flange (TDF corner inserts — square and fully crimped — in approximately 20 seconds. Similar to the Iowa Precision Cornermatic Plus HVAC Ductwork Corner Insertion Machine, the Cornermatic Plus Versa can sit on your workshop floor at an ergonomically comfortable table height. But the Cornermatic Plus Versa allows for greater flexibility during production by adding an in-ground, floor-level setting which allows for sliding over larger, heavier fittings and cut duct sections (heavy-duty hydraulic scissor lift raises and lowers the machine with a simple press of a button — machine goes from above ground to in-ground in less than 16 seconds).

E Product Details

Get a Quote

 Have a Question? Contact us.

The Iowa Precision Cornermatic Plus Versa HVAC Ductwork Corner Insertion Machine features:

Specifically designed for the fabrication of both small and large duct fittings from 16-26 gauge on one machine — from standard fittings to odd fittings like tight square throat elbows, flex connectors, offsets down to 2″ throats, and even the toughest inside or outside angle off-set transition fitting
Operator friendly above ground, table height setting is ideal for fabricating small fittings — adjustable legs to match most bench heights
Floor level setting allows for sliding over large duct sections and fittings to automatically insert the corners
Heavy gauge switch for 16-18 gauge performance and light gauge switch for 20-26 gauge performance enhances the Crimping process — slows the Cornermatic down for heavy gauge and speeds it up for light gauge
Completes eight (8) corner inserts in seconds
Fully automated — no switches or foot pedals — just push in and Cornermatic does the rest
Corners are inserted square and fully crimped — no need to change the crimping adjustment when inserting corners in 16 to 26 gauge fittings
Corners feed from below the work-surface allowing a clean, unobstructed work area
Light bar indicates when the material has fully engaged on the right or left side of the infeed guide clamps —green light = Go, red light = No
Light bar also indicates empty corner magazine
Works with SMACNA-conforming, T-25a and T-25b flange and many other flanged duct systems without changing settings
Each quick loading box holds eighty (80) corners and loads in ten (10)

Model	Capacity	Depth of Pocket	Other	Speed	Motor / Voltage	Dimensions / Weight
Iowa Precision Cornermatic Plus Versa HVAC Ductwork Corner Inserter Machine	16 to 26 gauge (.062" to .022" / 1.6mm to 0.6mm) Mild Steel Only	Flange Type for insertion: Transverse Duct Connector (TDC) and/or Transverse Duct Flange (TDF) — Customer to Specify	Model Capacity - Max 80 Corners StrapPak™ Quick-loading sleeve loads in 10 seconds	Approximately 2.5 seconds per corner	Electrical - 110/1/60 (Single Phase) Air - 85 to 100 PSI (5.5 - 7 Bar)	Length: 32" Width: 36" Height: 34" Weight: 600 lbs.